Microstructure and some properties of powder-pack borided Ti–5Mo–5V–8Cr–3Al alloy with special attention to the microstructure at the interface TiB/substrate

The borided layer was prepared on the surface of the Ti–5Mo–5V–8Cr–3Al alloy by powder-pack boriding at 1000°C-10h. SEM, EPMA and TEM were used to investigate the effects of alloying elements (Al, V, Mo and Cr) on the growth of TiB whiskers in the borided Ti–5Mo–5V–8Cr–3Al alloy. Wear properties of borided Ti–5Mo–5V–8Cr–3Al alloy were investigated using dry reciprocating friction tests. SEM results show that the thickness of boride layer in Ti–5Mo–5V–8Cr–3Al alloy is thinner than that in the Cp-Ti. This is attributed to the enrichment of alloying elements especially V in TiB/substrate by TEM, which hinders the diffusion of B atoms, thus resulting in the short and thick TiB whiskers in Ti–5Mo–5V–8Cr–3Al alloy. Borided Ti–5Mo–5V–8Cr–3Al alloy has the better wear resistance than as-received alloy.     

Influence of the SiC matrix introduction time on the microstructure and mechanical properties of Cf/Hf0.5Zr0.5C-SiC ultra-high temperature composites

C_f/Hf_0.5Zr_0.5C-SiC composites were prepared by introducing Hf_0.5Zr_0.5C matrix (11 cycles) and SiC matrix (9 cycles) into the carbon cloth preform through precursor impregnation and pyrolysis (PIP) process. The influence of the introduction time of SiC matrix on the microstructure and mechanical properties of C_f/Hf_0.5Zr_0.5C-SiC composites was studied, and the results show that with the increase of the PIP cycles of the SiC matrix introduced before Hf_0.5Zr_0.5C matrix, the composite open porosity decreased, and the flexural strength and modulus presented an obvious upward trend. CS45 sample, which has 4 cycles of PIP SiC introduced in advance, has the highest flexural strength, flexural modulus and interfacial shear strength of 402.73 ± 35.73 MPa, 56.92 ± 3.97 GPa and 100.88 ± 7.79 MPa, respectively. Hf_0.5Zr_0.5C matrix has a loose and porous structure, so when more SiC matrix was introduced in advance, its covering effect on the surface of fibers led to less intra-bundle pores and thusly denser composite structure, and due to the compactness of SiC matrix, better overall bonding of fiber, interface and matrix was achieved, as well as better load transfer effect, which led to obvious interfacial debonding and cracking based on the in-situ SEM observation during flexural tests. While in the sample without pre-introduced SiC, the cracking occurred mainly between the interface and porous matrix and the overall performance of the material was poor.     

Novel process for synthesizing fused mullite from titanium-rich medium/low grade or waste bauxite

This paper introduces a novel process to efficiently utilize medium-/low-grade or waste bauxite. The medium-/low-grade or waste bauxite is usually rich in iron oxide (total iron oxide content≥8%) or titanium dioxide (titanium dioxide content≥5%). In addition, both iron oxide and titanium dioxide have higher contents than typical bauxite (total iron oxide + titanium dioxide contents≥20%). It is difficult to obtain mullite with excellent properties using the process of beneficiation and sintering synthesis. Based on different reduction temperatures of K₂O, Na₂O, FeO_x, SiO₂ and TiO₂, the reduction of K₂O, Na₂O and FeO_x was set as the reduction end point. While SiO₂ start to be reduced, TiO₂ was unstable under high temperature and low oxygen partial pressure. The reason for the final formation of Ti₂O₃ in the TiO₂→TiO_2-x transformation process was analysed, and the morphology of the multiphase material obtained from the Ti₂O₃–3Al₂O₃·2SiO₂ solid solution was characterized. The reaction model was established.     

Growth mechanism and gas-sensing characteristics of organic-additive-free zinc oxide of various shapes

Zinc oxide is widely used in gas sensors, solar cells, and photocatalysts because of its wide bandgap and exciton binding energy of 60 meV in various metal oxides. To use ZnO as a gas sensor, it is necessary to synthesize it with surface defects and a large specific surface area. In this study, hydrothermal synthesis without surfactants was employed to obtain organic-additive-free ZnO. For morphology control, we varied the ratio of the hydroxide ion concentration to the zinc ion concentration. To confirm the growth mechanism of ZnO, we performed X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analyses. Raman spectroscopy and photoluminescence measurements were performed to analyze the surface properties. The Brunauer–Emmett–Teller method and probe stations were used to measure the specific surface area and sensitivity of the gas sensor, respectively. The results confirmed that flower-shaped ZnO is the most suitable gas-sensing material.     

Surface structure and quenching effects in BiFeO3-BaTiO3 ceramics

The structure and properties of Mn-doped 0.67BiFeO₃-0.33BaTiO₃ ceramics are systematically investigated with respect to the effects of annealing prior to rapid cooling by quenching in air. Air-quenching induces a change in crystal structure from pseudo-cubic to rhombohedral, with higher quenching temperatures leading to an increased rhombohedral distortion. These structural changes are correlated with the appearance of more well-defined ferroelectric domain configurations. It is shown that the surface preparation procedures for XRD measurements can induce significant changes in the peak profiles, indicating differences in crystal structure between the surface and bulk regions. Frequency dispersion in the temperature-dependent relative permittivity for the as-sintered sample is significantly reduced after quenching, accompanied by enhancement of the Curie point and improved temperature-stability of piezoelectric properties. It is proposed that the formation of defect clusters by A-site cation diffusion during cooling is circumvented by quenching, leading to the observed modification of structural distortion and ferroelectric properties.     

High ultraviolet transparent conducting electrodes formed using tantalum oxide/Ag multilayer

We investigated the optical and electrical properties of Ta₂O₅/Ag/Ta₂O₅ films as functions of the thicknesses of the Ta₂O₅ and Ag layers. It was found that with an increase in the thicknesses of the Ta₂O₅ and Ag layers from 10 to 40 nm and from 12 to 24 nm, respectively, the sheet resistance, carrier concentration, electron mobility, and resistivity of the Ta₂O₅/Ag/Ta₂O₅ film varied from 2.02 to 8.95 Ω/sq, 5.74 × 10²¹ to 2.92 × 10²² cm^–3, from 13.21 to 24.07 cm²/V·s, and from 8.89 × 10^-6 to 8.24 × 10^-5 Ω cm, respectively. The average transmittance (T_av) of the multilayer samples ranged from 57.18% to 93.99%, and it depended on the Ta₂O₅ and Ag layer thicknesses. The highest T_av of 93.99% was observed for the film with 35 nm thick Ta₂O₅ and 18 nm thick Ag layers, and the peak Haacke's figure of merit (157.04 × 10^–3 Ω^–1) was obtained for 20 nm thick Ta₂O₅ and 21 nm thick Ag layers. Ta₂O₅ (100 nm) and Ta₂O₅/Ag/Ta₂O₅ (20 nm/21 nm/20 nm) samples had optical bandgaps of 4.70 and 4.45 eV, respectively. Film Wizard simulations were conducted to understand the dependence of the transmittance of the multilayer on the thicknesses of the Ta₂O₅ and Ag layers, and phasor analyses were performed to determine how the transmittance of the Ta₂O₅/Ag/Ta₂O₅ (20 nm/21 nm/20 nm) film depended on the Ta₂O₅ layer's thickness.     

Simulation of thermal barrier coating spallation induced by the initiation/growth/coalescence of internal crack and interfacial crack based on a real image model

In the furnace cycle test, the growth of oxide film leads to the propagation and coalescence of multiple cracks near the interface, which should be responsible for the spallation of thermal barrier coatings (TBCs). A TBC model with real interface morphology is created, and the near-interface large pore is retained. The purpose of this work is to clarify the mechanism of TBC spallation caused by successive initiation, propagation, and linkage of cracks near the interface during thermal cycle. The dynamic growth of thermally grown oxide (TGO) is carried out by applying a stress-free strain. The crack nucleation and arbitrary path propagation in YSZ and TGO are simulated by the extended finite element method (XFEM). The debonding along the YSZ/TGO/BC interface is evaluated using a surface-based cohesive behavior. The large-scale pore in YSZ near the interface can initiate a new crack. The ceramic crack can propagate to the YSZ/TGO interface, which will accelerate the interfacial damage and debonding. For the TGO/BC interface, the normal compressive stress and small shear stress at the valley hinder the further crack propagation. The growth of YSZ crack and the formation of through-TGO crack are the main causes of TBC delamination. The accelerated BC oxidation increases the lateral growth strain of TGO, which will promote crack propagation and coalescence. The optimization design proposed in this work can provide another option for developing TBC with high durability.     

Community involvement critical for revitalization: Grass-roots initiative key to environmental remediation and restoration in the Great River (St. Lawrence River)

This paper describes the creation of an environmentally conscious community group, the Great River Network, and the role that it has played in the remediation and restoration process as part of one of the Great Lakes environmental programs. Community engagement was initiated in the region as part of the Remedial Action Plan for the Area of Concern at Cornwall/Akwesasne/Massena within the Upper St. Lawrence River. The community group formalised as a network representing 50+ organisations in response to perceived inadequacies in the agency of the community to respond to new environmental concerns outside of the scope of the existing programs. As a grass-roots initiative, the Great River Network has successfully completed remediation and restoration actions of significant value to the environment. These include a series of river clean ups (>42 tonnes of garbage removed), fish habitat restoration, and addressing shoreline erosion issues. Success has been achieved through partnering with a range of organisations, including Indigenous, non-profit, governmental, Conservation Authorities, businesses and industry partners. The action-oriented approach showcases how remediation and restoration led by, and embedded in, the community can result in true revitalization. A simplified framework for adaptive management practices for remediation and restoration efforts that lead to revitalization, including knowledge translation, is proposed. This case study highlights the transformational opportunities that remediation and restoration initiatives can bring. In this instance, the process is intensely local and cooperative and lays the foundation for moving towards a collective impact approach for the region.     

Joining zirconia with nickel-based superalloys for extreme applications by using a pressure-free high-temperature resistant adhesive

In order to meet the high demand for joining ceramic/superalloy composite structure in extreme environments, a novel high-temperature resistant adhesion technique was developed for joining ZrO₂ and Inconel 625 by applying an aluminum phosphate emulsion/zirconium sol based adhesive. With increasing temperature, a series of reactions occurred in adhesive, and its high-temperature bonding was attributed to the formation of a composite structure containing various ceramics and intermetallics. The adhesive after RT curing could find direct applications in extreme environments, and provide bonding strength no less than 2.5 MPa in the temperature range of RT-1100 °C. The bonding strength was higher than 4 MPa in the temperature range of 800–1000 °C, which was further attributed to the formation of an effective CTE-gradient relationship among ZrO₂, adhesive and Inconel 625, as well as the interfacial reactions between the two substrates. The work broadened the application of adhesion technique and brought new ideas for joining dissimilar engineering materials.     

Thermal stability of C/Mullite composites in different environments

In the present study, the mechanical properties and microstructure of C/Mullite composites with a PyC-SiC double-layer interfacial coating after annealing were systematically studied to evaluate the evolution of thermal stability in an inert atmosphere and a vacuum. The C/Mullite composites annealed in the inert atmosphere exhibited better thermal stability than those annealed under the vacuum. The main factor for failure of the composites was carbothermal reduction. The activation temperature of carbothermal reduction in composites in the inert atmosphere was ～100 °C higher than that in the vacuum. Once carbothermal reduction was activated, the microstructure of composites was destroyed, resulting in a significant weight loss and mechanical property degeneration. The degeneration of mechanical properties was unrecoverable.